Running ADAS: Difference between revisions

(11 intermediate revisions by the same user not shown)

Line 1:

==ADAS ~~assimilation~~ run==

==ADAS run==

===Build model===

Line 34:

aura_omi_bufr,ncep_satwnd_bufr,ncep_atms_bufr,ncep_sevcsr_bufr"

-->

Do Aerosol Analysis (y/n)? [y]

> n

Line 60:

Line 61:

<tt>$FVHOME/.FVROOT</tt> gives the location of the installation <tt>bin</tt> directory.

Some of these directories are stored in the archive. After completing the experiment, look in <tt>$ARCHIVE/g591p8</tt> (where <tt>g591p8</tt> is the experiment ID).

Some of these directories (<tt>ana/</tt>, <tt>chem/</tt>, <tt>diag/</tt>, <tt>etc/</tt>, <tt>obs/</tt>, <tt>rs/</tt>) are stored in the archive. After completing the experiment, look in <tt>$ARCHIVE/g591p8</tt> (where <tt>g591p8</tt> is the experiment ID).

====Run directory====

$ cd $FVHOME/run

<tt>g5das.j</tt> is the job submission script. The number of cpus etc. can be changed here (if they haven't already been changed during setup). Also, if you want to run a single cycle of <tt>GSIsa.x</tt> & <tt>GEOSgcm.x</tt> add <tt>exit</tt> right before 'PART IV'.

<!--

To simulate the OPS run d591_fpit, we make a few changes:

Line 79:

Line 81:

-->

===Data Assimilation ~~experiment~~===

===Data Assimilation===

$ cd $FVHOME/run

Line 86:

Line 88:

<tt>g5das</tt> creates a scratch directory <tt>$NOBACKUP/fvwork.xxxx</tt> and runs the experiment there. After the initial setup, <tt>GSIsa.x</tt> is run with output written to <tt>ana.log</tt> followed by <tt>GEOSgcm.x</tt> which writes its output to <tt>stdout</tt> and <tt>fvpsas.log</tt>.

===Forecast===

==Simulating OPS run==

<!--EVERYTHING BELOW IS COMMENTED OUT

~~====Forecast experiment====~~

~~Later.~~

==Simulating DAS forecast run==

Line 170:

Line 173:

-->

[[Category:SI Team]]

[[Category:Running the Model]]

@@ Line 1: / Line 1: @@
-==ADAS assimilation run==
+==ADAS run==
 ===Build model===
@@ Line 34: / Line 34: @@
      aura_omi_bufr,ncep_satwnd_bufr,ncep_atms_bufr,ncep_sevcsr_bufr"
 -->
   Do Aerosol Analysis (y/n)? [y]
   > n
@@ Line 60: / Line 61: @@
 <tt>$FVHOME/.FVROOT</tt> gives the location of the installation <tt>bin</tt> directory.
-Some of these directories are stored in the archive. After completing the experiment, look in <tt>$ARCHIVE/g591p8</tt> (where <tt>g591p8</tt> is the experiment ID).
+Some of these directories (<tt>ana/</tt>, <tt>chem/</tt>, <tt>diag/</tt>, <tt>etc/</tt>, <tt>obs/</tt>, <tt>rs/</tt>) are stored in the archive. After completing the experiment, look in <tt>$ARCHIVE/g591p8</tt> (where <tt>g591p8</tt> is the experiment ID).
 ====Run directory====
   $ cd $FVHOME/run
+<tt>g5das.j</tt> is the job submission script. The number of cpus etc. can be changed here (if they haven't already been changed during setup). Also, if you want to run a single cycle of <tt>GSIsa.x</tt> & <tt>GEOSgcm.x</tt> add <tt>exit</tt> right before 'PART IV'.
 <!--
 To simulate the OPS run d591_fpit, we make a few changes:
@@ Line 79: / Line 81: @@
 -->
-===Data Assimilation experiment===
+===Data Assimilation===
   $ cd $FVHOME/run
@@ Line 86: / Line 88: @@
 <tt>g5das</tt> creates a scratch directory <tt>$NOBACKUP/fvwork.xxxx</tt> and runs the experiment there. After the initial setup, <tt>GSIsa.x</tt> is run with output written to <tt>ana.log</tt> followed by <tt>GEOSgcm.x</tt> which writes its output to <tt>stdout</tt> and <tt>fvpsas.log</tt>.
+===Forecast===
+==Simulating OPS run==
 <!--EVERYTHING BELOW IS COMMENTED OUT
-====Forecast experiment====
-Later.
 ==Simulating DAS forecast run==
@@ Line 170: / Line 173: @@
 -->
 [[Category:SI Team]]
 [[Category:Running the Model]]